AstroStart RSS-2524 Instrukcja Użytkownika Strona 18
- Strona / 20
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
16
CAR FINDER
Press the
and buttons for 2 seconds.
This function sounds horn (short tune) and flashes parking lights to help you locate your vehicle in a large parking lot.
REMOTE SILENT MODE
The remote can be programmed to be used in silent mode.
Refer to the table of command on page 5 to know which button to press.
The audible confirmations from the remote control are Deactivated/Reactivated.
KEYPAD LOCK
The keypad of your remote can be locked to prevent any unwanted commands to be sent to your vehicle.
The keypad is locked or unlocked depending on its previous status.
Press the
, and buttons simultaneously for 2 seconds.
PANIC
Refer to the table of command on page 5 to know which button to press.
This command activates parking lights, siren, horn, and dome light intermittently, depending on which is connected to
system, for 30 seconds
or 60 seconds
depending on programming during installation.
Panic mode is used to attract attention if you are in difficulties.
If you are inside the vehicle when Panic Mode is activated, press on the brake pedal to lock doors (optional connections
required) and neutralize antitheft (60 sec. if doors were already locked). As long as the cycle is not over, applying the brakes
resets the sequence from the beginning every time.
This command will not be executed if engine is kept running by ignition key. In this case, parking lights will flash once to
confirm that command has been received. Use the stop command to abort panic mode.
START FAIL CODES
When a remote start attempt fails, it is possible to determine what caused the failure to start.
Refer to the table of command on page 5 to know which button to press depending on remote transmitter model being used.
The number of times the parking lights flash corresponds to the start fail code.
The table below lists the various start fail codes.
Code Failure to start details
1
Module has received a Stop command (remote or timer).
2
Brakes were applied during or after start sequence or module overload occurred.
3
Stopped by alarm.
4
Engine does not crank when starting sequence is initiated.
5
Start command ignored because hood is open.
6
Safety sequence not valid during start sequence.
7
Start command ignored because key is in the run position.
8
Remote starter main switch is "OFF" or output overload.
9
Runtime has elapsed.
10
Remote starter attempted to start engine three times unsuccessfully.
11
Remote starter sensed engine was already running.
12
Engine is over-revving (RPM > 3000) (programmable at time of installation).
13
Engine not cranking fast enough during start sequence.
14
Security sequence has been invalidated by status of parking brake.
15
Security sequence has been invalidated by opening of one or more doors.
16
Internal failure of module.
19
Module does not detect manual interface.
20
Consult your dealer.
If any of these start fail codes persist, consult your dealer.
- GOVERNMENT REGULATIONS 2
- Table of contents 3
- SAFETY PRECAUTIONS 4
- PREPARING SYSTEM 5
- THE REMOTE CONTROL 6
- TABLE OF COMMANDS 7
- START COMMANDS 8
- CONTINUOUS MODE 9
- TURBO MODE 9
- LOW TEMPERATURE MODE 10
- SETTING THE RUNTIME 10
- SECURITY SYSTEM (OPTIONAL) 11
- OPERATION 12
- TO TERMINATE ALARM CONDITION 13
- CONFIRMATION 13
- INDICATOR LIGHT 13
- ZONE CODES 14
- SECONDARY FUNCTIONS 14
- GLOSSARY 15
- LOCK / ARM 15
- UNLOCK / DISARM 16
- TRUNK RELEASE 16
- AUTOMATIC LOCK/UNLOCK 16
- OTHER COMMANDS 17
- CAR FINDER 18
- REMOTE SILENT MODE 18
- KEYPAD LOCK 18
- START FAIL CODES 18
- SAFETY CHECKS 19
- DETECTION OF DOOR OPENING 20
Powiązane produkty i podręczniki dla Zdalne rozruszniki AstroStart RSS-2524
(56 strony)EHEIM příručky
Seznam EHEIM produktových deivces obsahuje 8 uživatelské příručky a návody pro 8 modelů v 4 typech zařízení
Komentarze do niniejszej Instrukcji